When to Use This Checklist

This isn't a complete guide to dryer theory. It's a checklist for when you've got a quote in hand, you're about to send a PO, or — worse — you've already sent one and you're second-guessing it.

I've been handling industrial compressed air system orders for seven years. I've personally made (and documented) six significant sourcing mistakes, totaling roughly $23,000 in wasted budget. Now I maintain our team's checklist — the ten items below — to prevent others from repeating my errors.

If you're here, you're probably sourcing an industrial compressed air dryer, a desiccant compressed air dryer, or a full compressed air dryer system. These ten steps cover where most of the errors hide.

The 10 Checks

Step 1: Define Your Four Physical Parameters Before You Request Anything

Don't start with "what models do you have." Start with four numbers: flow (scfm or Nm³/min), working pressure (bar or psig), required pressure dew point (°F or °C), and inlet air temperature.

In Q1 2023, I sent an RFQ for 30 units of a refrigerated compressed air dryer with only "general shop use" written on it. Three vendors came back with three different interpretations. One quoted for +50°F dew point, which doesn't handle our piping. That was either a spec revision or a new RFQ — an extra week of back-and-forth, gone.

Checkpoint: Write a one-page spec and have every vendor confirm it in writing. If they can't confirm, they didn't read it.

Step 2: Match Dryer Type to Application — Before Brand or Model

Three families, and you need to decide which one fits:

  • Refrigerated compressed air dryer — for standard shop conditions, pressure dew points around +38°F
  • Desiccant compressed air dryer — for lower dew points (down to -40°F), outdoor piping, or sensitive processes
  • Compressed air dryer system — when flow, dew point, or installation constraints exceed what a single unit handles

This is one of the few places where being wrong is expensive across the whole batch. In September 2022, we ordered an entire batch of refrigerated units — the piping ran through an outdoor rack where ambient hits freezing. The units didn't survive the first winter.

Step 3: Confirm Which Dew Point Basis the Vendor Is Quoting

This is the step most people skip, and it's where more mix-ups originate than any other item on this list. Pressure dew point and atmospheric dew point aren't the same number. A desiccant unit at -40°F pressure dew point translates to a much higher atmospheric number — and if a vendor swaps one for the other in the quote, you won't notice until commissioning.

Checkpoint: Make the vendor write "Pressure dew point of Y°F at X psig" in the quote. If they can't write it, that's the risk, not a formatting issue.

Step 4: Check Capacity at Your Conditions, Not at Nameplate

Almost every nameplate capacity is rated at a specific set of conditions — 100°F inlet, 100 psig, 100°F ambient. Your actual conditions are probably worse. A refrigerated compressed air dryer rated 500 scfm at 100°F inlet, 100 psig might handle only 350 scfm at 110°F inlet and 90 psig — a 20-30% derate.

This is where the size lesson shows up. In 2019, I quoted seven units off nameplate only, and later found out we were the ones with the worst inlet conditions. Every unit was undersized by roughly a third.

Checkpoint: Ask for the capacity table at your actual conditions, not the standard spec sheet.

Step 5: Lock Power Supplies Before You Lock Models

In 2021, we bought a batch of industrial compressed air dryers from a European supplier on a 400V/50Hz default. Our facility runs 480V/60Hz. Every unit needed a transformer, and that was $4,300 in extra equipment and installation.

Checkpoint: Include frequency, voltage, phase, and — for desiccant units — control-circuit voltage in the spec.

Step 6: Walk the Installation Site — Actually Walk It

Physical installation constraints are not abstract. Port size, port orientation, connection type (threaded vs. flanged), and access clearances need to be verified on-site, not inferred from a datasheet.

A past mistake: on one installation rack, we needed 26 inches for maintenance access on the control side. The existing rack only had 18 inches. That was a re-pipe plus a delayed commissioning.

Checkpoint: Get a dimensioned installation layout, sign it off, and verify freight clearances before shipping.

Step 7: Match Certification and Pressure-Vessel Requirements to Your Jurisdiction

I'm not a mechanical engineer, so I can't speak to the ASME Section VIII calculations themselves. What I can tell you from a procurement side is: you need to confirm which code applies — ASME, CRN, PED, or another local standard — and you need documentation that proves the unit complies.

In 2020, we bought a batch of vessels with CE marking only. Our facility operated under ASME-rules. The units were rejected at the local inspection stage and required a full re-certification cycle.

Checkpoint: Have someone qualified verify the certification requirement upfront. Don't infer it from "the vendor says it's fine."

Step 8: Confirm Consumables and Aftermarket Support

For a desiccant compressed air dryer, the desiccant replacement cycle, availability, and price are the long-term cost drivers. For refrigerated units, it's refrigerant and filter elements. For a full compressed air dryer system, it's both plus controls and any proprietary components.

Ask: can you source these consumables in your region on a predictable lead time, or are you waiting six weeks every time one wears out? We once squeezed a vendor hard on purchase price, then found the desiccant was 40% above market and had a longer replacement cycle. The savings evaporated on the first change-out.

Step 9: Turn Acceptance Criteria into Contract Language

Don't leave acceptance at "meets spec." Write the measured flow, pressure, and dew point — tied to the parameters from Step 1 — into the contract.

We had a situation where "site acceptance test" was ambiguous, and chasing the post-acceptance report took six weeks. That became its own project management line item. If it had been written clearly in the contract, it would've been a one-week item.

Step 10: Test Vendor Response Speed Before You Commit

This is the step most people skip — possibly the most counterintuitive one on the list. Before finalizing any PO, send the vendor one question: "If this unit failed in the field next month, what's your service response time, and who's the named contact?"

Grade the answers. I've asked 11 vendors that question. Three gave specific response windows and a named person. The rest gave "as soon as possible" or "24-48 hours." The three are the ones we keep coming back to. That's a proxy signal you can't get from a spec sheet or a discount schedule.

Notes and Common Mistakes

This isn't a checklist that demands perfection. Running through it takes about ten minutes. But that's the point: five minutes of verification beats five days of correction, and it's usually cheaper than a few hundred dollars in rework on the back end.

A few notes from my own mistakes:

  • Steps 2 and 3 are where most of the actual money gets spent wrongly. Skipping them resets everything downstream.
  • If pressure-vessel certification isn't your area, hand Step 7 to someone qualified. Guessing is exactly how a rejected shipment happens.
  • Pricing references in this article reflect Q3 2025 costs. Rates move — verify current numbers before budgeting, especially on imports.
  • If a quote doesn't state capacity conditions explicitly, treat that omission as the risk itself. A lower quote on paper isn't necessarily a lower total cost.

If you only do one thing from this list, do Step 1. The rest of the checklist hangs on whether you can put flow, pressure, dew point, and inlet temperature on one page. Everything else — dryer type, model, quote comparison — is derived from those numbers. Get them written down and errors leave the workflow; leave them in your head and they show up on the floor.

I've made that mistake. You probably don't need to.